PRODUCT INTRODUCTION
Model Number:I02
Overview
i02 is a main stream SMART wireless Router, provides stable and secure Internet access for users. Its CPU runs at the speed of up to 450 Mhz, to provide high performance of the CPE. It provides up to 100/100Mbps up/downstream, and supports 802.11b/g/n wireless standards, which is up to 300 Mbps wireless transfer speed.
MIMO and Beam Forming technologies provide for better throughput and superior signal coverage.
Setting up the CPE is very convenient and SMART. Setup will need only 2 steps. It will detect the WAN connection method automatically. Secondly, user may need to only input PPPoE user name/password, and the SSID name/password.
The “i” series UI system allows user to go use even advanced configurations with Graphic instructions.
2 Antennas for coverage in vertical direction as well.
MIMO for higher Wireless throughput rate.
Supports Beam forming - the AP will automatically detect the remote device and concentrate more power in the optimum direction.
Very simple to use GRAPHIC CONFIGURATION user interface.
Minimal configuration with devices using SMART Repeater function feature by maker.
Mobile APP support
Hardware Specification
Chipset | Realtek 8676S + 8192ER |
Flash | 4MB |
RAM | 16MB |
WAN | 1 Fast Ethernet ports (10/100Mbps) |
LAN | 4 Fast Ethernet ports (10/100Mbps) |
Wireless | 802.11 b/g/n, up to 300Mbps; 2X5dbi external antenna |
USB | USB2.0 Host |
LED | Power WAN Internet LAN1 LAN2 LAN3 LAN4 WLAN USB (Power and Internet are dual color) |
Input Power | 12V 1A |
Accessories | RJ45 cable 1.5M X2; PSU 12V 0.5A EU plug 1.5M wire, 110V ~240V |
Gift box | Brown with “iRouter” logo and MAC/SN sticker |
Others | One Reset button, MAC/SN sticker and foot cushion on the bottom |
Housing: SH | |
MAC: DP MAC; SN: DP SN- DPI02CC408XXXXXXX* *DP mean Dragon Path; I02 means DP model; CC means customer code of Client 4 means production year 2014; 08 means production month August the following number is the production sequence number | |
Dimensions | TBD |
Installation | Wall mounting & desktop mounting |
Power consumption | <6W (without external USB device) |
Environmental | Temperature: - 0 to 50 ℃(Standard Operating) - -20 to 70 ℃ (Non-operating) Humidity: - 10% to 90% (Non-condensing, Standard Operating) - 5% to 95% (Non-condensing, Non-operating) |
Firmware Specification
Protocol & Features Supported | |
1 | RFC 2684 IP Bridging & RFC 2684 IP Routing |
2 | RFC 2516, PPPoE (Point over Ethernet) over ATM |
3 | RFC 2364 PPPoA |
4 | Support multiple Routing service (optional) |
5 | QOS based on service and ports |
6 | Routing: RIP v1, RIP v2 |
7 | Support Static Routing |
8 | NAT & PAT (RFC 1631) |
9 | DMZ support |
10 | NAT with Application Layer Gateway |
11 | IP Routing: TCP, UDP, ICMP, ARP |
12 | DHCP Client/Server/Relay |
13 | IP multicasting IGMP v1/v2 |
14 | Pass through/open/redirection and port mapping |
15 | QoS for bandwidth control |
16 | HTTP (web based) for firmware upgrade & configuration |
17 | IP filter |
18 | IGMP Snooping |
19 | IEEE 802.1D Transparent Bridging |
20 | DNS relay |
Firewall Features | |
1 | Source IP address, Destination IP address, Source port addresses, Source MAC address, Destination Port address |
2 | Stateful packet inspection |
3 | Filtering on Application basis |
4 | Filtering on port basis |
Virtual private network support | |
1 | Standard (IPSec, L2TP, PPTP) pass through |
2 | Compatibility with other IPSec VPN gateways |
3 | Supports multiple simultaneous login via FTP/www/Telnet |
Diagnostic | |
1 | support diagnostic function |
Management features & functionalities | |
1 | TFTP/FTP upgrade |
2 | Support TR069 (optional) |
3 | Telnet remote access support |
4 | support Web based configuration |
5 | Support for backup & restore configuration to/from PC |
6 | Support TR-64 for LAN management |
7 | Support DHCP server for IP management |
Quality of Service requirement | |
1 | Port based and IP based QoS |
2 | 802.1bit marking |
General Specification & Operational requirement | |
1 | System Log |
2 | IPv4/IPv6 Dual Stack |
Applicable for WiFi CPE | |
1 | Wireless Standard and feature - 802.11g/802.11b/802.11n |
2 | 64/128 bit WEP support |
3 | MAC association control |
4 | Support Multiple SSIDs |
5 | Support for WEP, WPA, WPA2, WPA2 Enterprise(802.1X)* * Can not support smart connect for WPA2 Enterprise(802.1X) |
6 | “0 Configuration” function with i01 smart repeater, to simply expand WiFi coverage with high performance. |
7 | Files Storage System for WAN and LAN ( available on phase 2) |
Scan the qrcode to reading this article on your phone